The WeShape Mobile Stand is designed to hold your red light panel so it can be positioned where it feels most useful and comfortable for your recovery routine. The stand is height-adjustable and rolls on four casters, so you can move it between rooms.
This guide walks through the safety notes, parts list, the six assembly steps, final setup checks, dimensions and storage, and warranty terms. Before beginning, take a few minutes to review the parts list, safety notes, and installation steps.
Important Safety Notes
Please read these safety notes before assembling your stand. Improper installation or assembly may result in injury or property damage.
If any instructions are unclear, or if any hardware is missing or damaged, contact WeShape Support at [email protected] before continuing.
Do not assemble or use the stand if the product or hardware is damaged or incomplete.
Maximum supported weight: 39.68 lbs / 18 kg.
This product contains moving parts. Use with care when adjusting or relocating.
Use this stand only for its intended purpose.
Do not modify the stand or use it outside the recommended weight range.
Keep children away from the stand and mounted equipment. Climbing, pulling, or playing near the stand may cause tipping or injury.
Do not place toys, remote controls, or tempting objects on mounted equipment where children may try to reach them.
Using the stand with equipment heavier than the recommended weight limit may cause instability.
Parts List
Before starting, lay out all parts and hardware and match each piece to the parts list to make sure everything is included.
Item | Description | Qty |
a | Base tube | 1 |
b | Base tube | 1 |
c | Connecting pipe | 1 |
d | Support rod | 1 |
e | Lift rod | 1 |
f | Lift rod | 1 |
g | Plastic ring | 2 |
h | Mounting bracket | 2 |
i | Handle screw (M8 × 50MM) | 3 |
k | Handle screw (M8 × 15MM) | 6 |
l | Long screw (M8 × 55MM) | 4 |
m | Caster | 4 |
n | Screw (M8 × 65MM) | 4 |
o | Allen key (M8 × 130MM) | 1 |
Installation Steps
The assembly diagrams are in the PDF manual, available on the Product Manuals page. Keep it open alongside these steps.
1. Attach the Casters and Join the Base
Turn over the base and securely attach the four casters (m) at positions m1, m2, m3, and m4.
Insert the left and right base tubes (b) into the connecting pipe (c) and fix them with screws (n) at positions n1, n2, n3, and n4.
2. Install the Support Rod
Insert the support rod (d) into the base and screw it in with the long screws (l) at positions l1, l2, l3, and l4.
3. Install the First Lift Rod and Set Your Height
Insert the lift rod (e) into the support rod (d), and choose an appropriate height.
Refer to the first observation hole to locate the bracket position, then use the handle screw (k) to fasten the lift rod at the second hole. After that, lock and insert another handle screw from the side of the rod to reinforce the structure.
Place the plastic ring (g) inside the support rod (d).
4. Install the Second Lift Rod
Insert the lift rod (f) into the support rod (e). Place the plastic ring (g) inside the support rod (e).
5. Attach the Mounting Arm
Attach the mounting arm using handle screws (k) and (i), as shown in the manual's diagram. Tighten the screws by hand first, then secure them fully once everything is aligned.
6. Attach the Mounting Bracket
Attach and secure the mounting bracket using screws (k) and (i).
Before placing equipment on the stand, check that:
All screws are tightened
The stand is stable
The wheels are positioned safely
The mounted equipment does not exceed 39.68 lbs / 18 kg
Final Setup Check
Before using the stand:
Make sure all hardware is fully tightened
Confirm the stand rolls smoothly
Lock or stabilize the wheels if needed
Keep the stand on a flat, stable surface
Keep children and pets away from the stand during use
Dimensions & Storage
Width: about 24 inches at the widest point, including casters
Base footprint length: about 30.5 inches
The stand is designed to stay fully assembled. It does not fold, collapse, or allow the base rails to narrow for storage, so plan for a dedicated spot to keep it when it's not in use.
Warranty
Your WeShape Mobile Stand includes a 2-year limited warranty covering defects in materials or workmanship under normal use, for products purchased by the original customer. Defective products or parts may be repaired, replaced, or refunded after the issue is reviewed.
The Warranty Does Not Cover
Damage from misuse or negligence
Improper maintenance
Product modification
Unauthorized repairs
Damage during storage or transportation
Theft or loss
Do not disassemble or attempt to repair the product yourself. Unauthorized repair attempts may create risk of injury and may void the warranty.
Making a Warranty Claim
Message us through the chat widget or email [email protected] with:
Your order number
A brief description of the issue
Photos or a short video showing the problem
Keep your proof of purchase, since we may need it to process a claim, and please don't send anything back before contacting us. For full details, see What warranty comes with my WeShape recovery products?
Tips & Reminders
Lay out and check every part against the parts list before you start. It's much easier than backtracking mid-assembly.
Tighten screws by hand first, then fully secure them once everything is aligned.
The maximum supported weight is 39.68 lbs / 18 kg. Do not exceed it.
Always use the stand on a flat, stable surface, and lock the wheels if needed.
Set up the stand carefully and take your time. A stable setup makes your red light routine easier, safer, and more supportive.
WeShape products are not intended to diagnose, treat, cure, or prevent any disease.